2004 Jeep Grand Cherokee 4.7 Plastic Hose Diagram
Joined
·
13,095 Posts
Discussion Starter · #1 ·
hey guys havent been on JG in months but i have a major problem and need some help. i changed my spark plugs today and must have moved the pcv line while doing the last plug. i think i knocked it out of the back of the engine, but i dont know where it goes back in. now my jeep idles between 1300-1800rpms instead of around 300-500 like normal. from what i could see it looks like the hose goes into a small plastic elbow behind the engine and it looks like mine is cracked. i am supposed to be going on a long trip tomorrow but i cant go if i dont get this fixed. does anyone know if this would likely be the cause? if so how do i fix it? i cant see back there and there arent any diagrams online that i can find. has anyone here done this repair? i dont see how this line can be removed and replaced with the engine in the vehicle. any help would be appreciated!!
Joined
·
2,807 Posts
You have it like I said in my PM, if you need additional help im sure the pictures diagrams at the dealer will clear things up. Though basically what you have seen is what is there... This WILL cause the high idle. for Chrysler products they use speed density, an air flow calculation. as such when a vacuum leak is introduced it just sees more air and adds more fuel causing your high idle.... if it was a mass air flow car that actually used a device to measure the air, then unmetered air would not be met with additional fuel so it runs like crap (if it runs at all).
I made my trip repair suggestion in the pm but you will want to replace the hose.
Joined
·
13,095 Posts
Discussion Starter · #3 ·
You have it like I said in my PM, if you need additional help im sure the pictures diagrams at the dealer will clear things up. Though basically what you have seen is what is there... This WILL cause the high idle. for Chrysler products they use speed density, an air flow calculation. as such when a vacuum leak is introduced it just sees more air and adds more fuel causing your high idle.... if it was a mass air flow car that actually used a device to measure the air, then unmetered air would not be met with additional fuel so it runs like crap (if it runs at all).
I made my trip repair suggestion in the pm but you will want to replace the hose.
thank you!! hopefully i can get a hose tomorrow! i think the elbow was cracked for awhile and i just knocked it off the fitting.
Joined
·
13,095 Posts
Discussion Starter · #4 ·
anyone have a part number for the pcv tube on a 06 4.7? i lost my parts catalog when i got a new computer
Joined
·
4,628 Posts
anyone have a part number for the pcv tube on a 06 4.7? i lost my parts catalog when i got a new computer
There appear to be a variety of bits under that description.
I'd google and look at the pictures from the online dealers selling parts.
I take it may be too far gone to duct tape?
Joined
·
13,095 Posts
Discussion Starter · #6 ·
There appear to be a variety of bits under that description.
I'd google and look at the pictures from the online dealers selling parts.I take it may be too far gone to duct tape?
i cant find anything online about it, i havent pulled the hose out yet but i could see the crack. local dealer wants $55 for the hose
Joined
·
989 Posts
It's hard to tell, but I think the part number is this one (based on your description of its location):
53032617AD 1 EV0 TUBE, Crankcase Vent To Intake
Manifold
If not, it could be:
53013757AA 1 EV0 TUBE, Crankcase Vent To Air
Googling that part number gets a number of hits in the $25 range.
Joined
·
13,095 Posts
Discussion Starter · #8 ·
i need number one on this diagram. so 53032617AD is correct, thank you! i guess they wanted $52 for that $23 part.
Joined
·
13,095 Posts
Discussion Starter · #9 ·
i also assume that diagram is generic, because my hose has an elbow on the part that connects to the back of the engine
Joined
·
13,095 Posts
Discussion Starter · #10 ·
i fixed it today using the existing part. wasnt as hard as i thought it would by to reattach the hose. i bought a mechanics inspection camera at walmart for $50 and it worked wonders!!
Joined
·
989 Posts
Great to hear - those types of repairs are the best, and you get a new tool out if it.
Joined
·
13,095 Posts
Discussion Starter · #12 ·
Great to hear - those types of repairs are the best, and you get a new tool out if it.
Hah i know right? I have already used it to check brake pads with the wheels still mounted
Joined
·
2,015 Posts
I love my walmart inspection camera.
Joined
·
1,019 Posts
I love my walmart inspection camera.
Link to the model you guys are talking about? I've had one on my list of things to buy for a while now...
Joined
·
2,015 Posts
I got mine on Black Friday. The brand is whistler
Joined
·
1,019 Posts
Joined
·
2,015 Posts
Yea that's the one I have.
Joined
·
13,095 Posts
Discussion Starter · #18 ·
That is the one i have also, cant beat the price!!
Posted by: tuweflene0197835.blogspot.com
Source: https://www.jeepgarage.org/threads/high-idle-like-due-to-pcv-hose-disconnection.69860/
Post a Comment for "2004 Jeep Grand Cherokee 4.7 Plastic Hose Diagram"